Modern PC Board Design Practices
audioXpress|March 2023
Tips and Techniques
Ethan Winer
Modern PC Board Design Practices

In Part 1 of this article Ethan Winer gave a general overview of modern PC board design using surface-mounted devices (SMDs). Part 2 continues with specific techniques and advice.

As explained in Part 1, unless your electronic device is fairly simple, a four-layer board makes sense because it offers dedicated ground and power planes in the middle, as well as a bottom layer for additional traces or power. This also avoids having to run both signal and power traces on the same layer that might complicate routing. Further, the inner layers avoid capacitive coupling between top and bottom traces that could, for example, cause a high-gain op-amp to oscillate if its input and output traces are opposite each other for much of a distance.

The top layer holds the component pads and most of the connecting traces, with the inner ground layer beneath. Then another inner layer carries power around the board, with the bottom layer available for any additional traces that can't fit on top. To my thinking, laying out the routing of a PC board is somewhat like playing chess. You not only have to solve the current problem of how to connect component A to component B, you also have to think ahead several moves: If I put R35 here, will that block pin 6 of the op-amp from connecting to C12 over there? Would it help if I rotate the dual NOR gate 180 degrees?

As Figure 8 shows, besides laying out the board traces, it's just as important that the component labels (R12, C14 etc) on the silk screen layer clearly identify their related parts. Especially with tightly packed boards like my current project.

This story is from the March 2023 edition of audioXpress.

Start your 7-day Magzter GOLD free trial to access thousands of curated premium stories, and 9,000+ magazines and newspapers.

This story is from the March 2023 edition of audioXpress.

Start your 7-day Magzter GOLD free trial to access thousands of curated premium stories, and 9,000+ magazines and newspapers.

MORE STORIES FROM AUDIOXPRESSView All
Perspectives on Automotive Sound Design - In the Era of Electric Vehicles
audioXpress

Perspectives on Automotive Sound Design - In the Era of Electric Vehicles

From combustion engine vehicles to fully electric vehicles, and from sound systems in the car to sound design and synthesis for the car itself, everything is changing in the automotive industry. This conversation with two members of the DSP Concepts automotive team with vast experience in the field, John Whitecar, VP of Product Management, and Steve Ernst, Head of Business Development, offers valuable insights on how things are evolving.

time-read
10+ mins  |
June 2023
Audioscenic: From Vision to Product
audioXpress

Audioscenic: From Vision to Product

Audioscenic is an innovative 3D audio beamforming technology company spun off from the University of Southampton. It is a remarkable example of perseverance, from early development to the first commercial implementation, which audioXpress considered Best of Show at CES 2023. This article shares the story so far, as Audioscenic continues its groundbreaking journey exploring consumer applications for its forward-thinking approach to spatial audio.

time-read
8 mins  |
June 2023
The Changing Audio-Ecosystem in Electric Vehicles
audioXpress

The Changing Audio-Ecosystem in Electric Vehicles

The rapid shift to plug-in hybrid and full-battery electric vehicles is having a significant and long-lasting impact on how audio systems are integrated into cars. While some noises are much more prominent due to the absence of the familiar engine noise, the transition offers exciting possibilities for sound systems, passenger entertainment, and enhancing the overall automotive experience.

time-read
10+ mins  |
June 2023
A (Z)OTL with 300Bs: Part 1-The Makeover
audioXpress

A (Z)OTL with 300Bs: Part 1-The Makeover

Rebuilding an amplifier for reasons of better reliability, better aesthetics, or bringing it up to the latest standard can be very rewarding. And if it is a classical, technological grandstand, even more so. Thomas Perazella embarked on such an adventure with a famous David Berning ZOTL amplifier. In Part 1 of this article, Tom presents the amplifier and discusses its unique circuitry. In Part 2, he will proceed to dismantle and rebuild the amp for the new owner and place it in a new chassis

time-read
10+ mins  |
May 2023
The Hypex NCORE NCx500 Amplifier Module
audioXpress

The Hypex NCORE NCx500 Amplifier Module

NCORE (NC) amplifier modules are the flagship product from Dutch manufacturer Hypex Electronics and its success among the high-end audio brands is well documented. In 2022, Hypex announced the introduction of its improved NCOREX technology, starting with the NCx500 OEM module, which audioXpress received for review

time-read
10+ mins  |
May 2023
Monoblock Power Amplifier with Precision Bias Control
audioXpress

Monoblock Power Amplifier with Precision Bias Control

In Part 2, Bruce Gillingham discusses the remainder of the MB1's circuitry, its mechanical design, and its performance measurements

time-read
10+ mins  |
May 2023
A Trip Down Memory Lane
audioXpress

A Trip Down Memory Lane

The history of tube application began with radio receivers, the telephone system, and cinema sound systems. Later, tubes began to be used in home stereo systems, and in amplifiers for electric guitars. Today, the primary markets for tubes are high-end stereo and musical instrument amplifiers. In this article Richard Honeycutt remembers his first contact with \"starter\" guitar amps as a teenager, progressing throughout his days as a semi-pro musician

time-read
5 mins  |
May 2023
The Vanderveen Trans PP80 Valve Amplifier
audioXpress

The Vanderveen Trans PP80 Valve Amplifier

This new push-pull (PP) valve amplifier, featuring the Trans technique, delivers 80W power, refined resolution, valve-sound envelopment, and low distortion plus good speaker damping. And... the amp is simple to construct

time-read
10+ mins  |
May 2023
Accuracy in LTspice Modeling
audioXpress

Accuracy in LTspice Modeling

Sometimes we need to consider the human factor when using circuit design simulation tools. In this article, our hollow-state expert details an error that occurred in a past article, which is now being corrected.

time-read
4 mins  |
March 2023
Transitioning Audio Tests from R&D to the Production Line
audioXpress

Transitioning Audio Tests from R&D to the Production Line

Production line audio testing poses many challenges such as noisy environments, harsh operating conditions, high throughput, relative limits, and more. In this article, Steve Temme shares his observations and outlines the main considerations to ensure a successful operation.

time-read
10+ mins  |
March 2023